Hi,
now i tried to program my 123 tune+ with an Ipad with Bluetooth 4.0
I works so far. The prpgramming of the centrifugal advance works fine.
The programming of the vacuum advance is catastrophic.
At the beginning the "save" comes only sometimes (wrong entries ?)
Now ist impossible to change anything on the vacuum and the save button is dead.
When i cancel lines it works when i press insert line the app crashes.
The "save" button never will be active.....
And now ?????
Help !!!!
Thomas
PS is it possible to reset the 123 tune+ ?
Dear Thomas,
to reset the 123/TUNE+:
- Close down all 123TUNE Apps (very important!!! )
- Turn off the power of the engine
- Disconnect the black wire from the coil and connect it with the red (+ 12 Volt) wire.
- Turn the power on. The blue LED will flash for about 10 seconds, DO NOT interrupt this proces.
- When the blue LED lights continuously, the reset procedure is complete.
- Turn off the power again and re-connect the black wire to the ( - ) side of the coil.
NB for Dutch customers: Nederlandse tekst tref je hieronder aan.
Best regards,
Leen,
123ignitionshop.com & Leen APK
- Sluit alle 123TUNE Apps af. ( belangrijk!!! )
- Zet het contact uit
- Haal de zwarte draad van de bobine en steek deze bij de rode ( + 12 Volt ) draad.
- Zet het contact aan. De blauwe LED gaat nu ongeveer 10 seconde knipperen, breek dit proces niet af.
- Als de blauwe LED continu brand is de reset procedure geslaagd.
- Zet het contact weer uit en sluit de zwarte draad weer aan op de ( - ) kant van de bobine.
Hello,
thx for the answer.
I resetted the 123 Tune+ several times with no success.
The programming of the vacuum advance does not work, the app crashes, no save button active.
!!! When the 123 was new ist was working !!!
Now i testet the android and ipad app, same problem :(
How can i fix this problem, now i must replace the 123 tune+ with my old 123, not good.
Please help me
THX
Thomas
I have the exact same problem. I am running version 1.5.2 on Android 7.1.2 (Nougat). The map curve function doesn't allow me to save, modify, add or remove any points to the curve. The app often crashes when I open the Map function at all.
The map curve is as follows:
http://imgur.com/a/T3N0I
Point / KP / Advance
1 | 0 | 0.0
2 | 29 | 0.0
3 | 40 | 7.0
4 | 75 | 9.0
5 | 200 | 0.0
I have similar/same problem.
Android 7.1.1 on SONY E6853. BT connection comes up then disappears almost immidiately. Gave up. Then installed app on SAMSUNG Tablet. More stable connection but cannot change advance (save button shade suggest save is not featured.
Help!
I have the same problem (iPhone 6s). What is the solution? Should I reload the app from the Apple store?
Multiple requests for a solution have gone unanswered.
I’m totally confused with all of this. Are you supposed to enter advance curve values yourself or does the 123 come with them already installed, if your distributor has been converted, rather than a newly bought item?
Turning the ignition on seems to produce the advance curve graph for my engine on the app but I’ve no idea whether it is reading it from the 123, or not. At this stage the engine has not started, in fact I cannot get it to fire up at all. So far this conversion has been a complete waste of time and I’m seriously considering having it converted back to standard set up. Life’s too short and I want to drive the car!
My 123tune+ bluetooth is not possible to connect anymore. Very very dissapointing! I have reset the system, I have tried with Sony experia 8.0 twice, no connection.
I have tried with I-Phone twice where it seems to connect but it is not possible to type any letters for the PIN ?
I have bought this expensive device as a professional component, not as a toy!
If I not will get any support that works on Monday I will send it back.
Karl
